LED display and diode manufacturer,Betlux LED digital world, share with you the quality LED technology

3.00 inch single seven segment led display

BL-S300A-11,BL-S300B-11

seven segment display circuit | 7 segment display

Brand	BETLUX
Part NO	BL-S300A-11,BL-S300B-11
Dimension	70.00110.0013.00 mm
Weight	84.0000g
Package	4pcs/bag
Datasheet

Ask a question about this product

Feature: Description Low Current Operation
Common Anode and Common Cathode available
Excellent Character Appearance
High Light Output
Easy Mounting On PC Boards or Sockets
IC Compatible
Multicolor Available
Categorized for Luminous Intensity
Technically Rugged
Standard: Gray Surface, White Segment
RoHs Compliance

Electrical-optical characteristics:

Part No C.C.	Part No C.A.	color	wavelength	V typical(V)	V max(V)	Brightness(mcd)
BL-S300A-11D	BL-S300B-11D	Super Bright Red	660	1.85	2.2	300
BL-S300A-11S	BL-S300B-11S	High Bright Red	660	1.85	2.2	210
BL-S300A-11UR	BL-S300B-11UR	Ultra Bright Red	660	1.85	2.2	320
BL-S300A-11E	BL-S300B-11E	Orange	635	2.1	2.5	210
BL-S300A-11UE	BL-S300B-11UE	High Bright Orange	630	2.1	2.5	215
BL-S300A-11Y	BL-S300B-11Y	Yellow	585	2.1	2.5	210
BL-S300A-11UY	BL-S300B-11UY	High Bright Yellow	590	2.1	2.5	215
BL-S300A-11G	BL-S300B-11G	Green	570	2.2	2.5	210
BL-S300A-11UG	BL-S300B-11UG	High Bright Green	574	2.2	2.5	300
BL-S300A-11PG	BL-S300B-11PG	Super Pure Green	525	3.0	4.2	350
BL-S300A-11B	BL-S300B-11B	Super Bright Blue	470	3.0	4.2	215
BL-S300A-11UB	BL-S300B-11UB	Super Bright Blue	470	3.0	4.2	250
BL-S300A-11W	BL-S300B-11W	White	-	2.7	4.2	270

Package configuration & Internal circuit diagram

All dimensions are in millimeters(inches)
Tolerance is +-0.25(0.01") unless otherwise note
Specifications are subject to change without notice.

Absolute maximum ratings (Ta= 25?C)

Reflector Surface color (1st number)/ Segment Lens color (2nd number):

Number	0	1	2	3	4	5
Ref Surface Color	White	Black	Gray	Red	Green
Epoxy Color	Water clear	White diffused	Red Diffused	Green Diffused	Yellow Diffused

Absolute maximum ratings (Ta= 25°C)

Parameter		S	D	UR	E	Y	G	Unit
Forward Current IF		25	25	25	25	25	30	mA
Power Dissipation Pd		60	60	60	60	60	65	mW
Reverse Voltage VR		5	5	5	5	5	5	V
Peak Forward Current IPF (Duty 1/10 @1KHZ)		150	150	150	150	150	150	mA
Operation Temperature TOPR	-40 to +80							°C
Storage Temperature TSTG	-40 to +85							°C
Lead Soldering Temperature TSOL	Max.260+ 5°C for 3 sec Max. ( 1.6mm from the base of the epoxy bulb)							°C

Absolute maximum ratings (Ta= 25°C)

Parameter	UHR	UE	YO	UY	UG	PG	UB	UW	Unit
Forward Current IF	30	30	30	30	30	30	30	30	mA
Power Dissipation Pd	75	65	65	65	75	110	120	120	mW
Reverse Voltage VR	5	5	5	5	5	5	5	5	V
Peak Forward Current IPF (Duty 1/10 @1KHZ)	150	150	150	150	150	150	100	100	mA
Operation Temperature TOPR	-40 to +80								°C
Storage Temperature TSTG	-40 to +85								°C
Lead Soldering Temperature TSOL	Max.260+ 5°C for 3 sec Max. ( 1.6mm from the base of the epoxy bulb)								°C

Partno description:

LED seven segment , called also LED numeric display, is widely applied in home appliance panel display and other application.

Related Information

Applied for:

1. Application
The Seven Segment LED is widely applied for ordinary electronic equipment (such as office equipment,
communication equipment and household applications). Checking with BETLUX's Sales in
advance for information on applications in which exceptional reliability is required, particularly
when the failure or malfunction of the LEDs may directly jeopardize life or health (such as in
aviation, transportation, traffic control equipment, medical and life support systems and safety
devices).

2. Storage
The storage ambient for the Seven Segment LED should not exceed 30℃ temperature or 70% relative humidity.
For extended storage out of their original packaging, it is recommended that the Seven Segment LEDs be stored
in a sealed container with appropriate desiccant, or in a desiccator with nitrogen ambient.

3. Cleaning
Avoid using any unspecified chemical solvent to clean LED . For example, Trichloroethylene, Chlorosen, Acetone, and Diflon S3MC.
Any cleaning method can only be taken under normal temperature in one minute or less if it is required.
Use water to clean the Seven Segment LED if necessary under room temperature
dry it immediately after that.

4.Forming
Any unsuitable stress applied to the epoxy may break bonding wires in LED
Any forming on lead pin must be done before soldering, not during or after soldering.
Avoid applying any stress to resin in order to prevent the epoxy fracture and break on bonding wire.
While forming, please use a tie bar cut or equivalent to hold or bend the pin.
2mm from the base of resin is the minimum distance for the place bending the lead pin.
Avoid bending the lead pin at the same point twice or more.

seven segment display forming caution

Soldering

When soldering, leave a minimum of 2mm clearance from the base of the base of the lens to the soldering point. Dipping the lens into the solder must be avoided.

Do not apply any external stress to the lead frame during soldering while the LED is at high temperature.

Recommended soldering conditions:

IR Reflow Soldering (for SMD display)		Wave Soldering		Soldering Iron
Pre-Heat	150-180°C	Pre-Heat	100°C Max.	Temperature	300°C Max.
Pre-Heat Time	120sec Max.	Pre-Heat Time	60sec Max.
Peak Temperature	260°C Max.	SolderWave	260°C Max.	Soldering Time	3sec Max.(one time only)
Soldering Time	10 sec Max.	Soldering Time	5sec Max.

Note: Excessive soldering temperature and/or time might result in deformation of the LED lens or failure of the LED

ESD(Electrostatic Discharge)

Static Electricity or power surge will damage the LED.

Suggestions to prevent ESD (Electrostatic Discharge):

n Use a conductive wrist band or anti-electrostatic glove when handling these LEDs

n All devices, equipment, and machinery must be properly grounded

n Work tables, storage racks, etc. should be properly grounded

n Use ion blower to neutralize the static charge which might have built up on surface of the LED's

plastic lens as a result of friction between LEDs during storage and handling

ESD-damaged LEDs will exhibit abnormal characteristics such as high reverse leakage current,

low forward voltage, or “no light on” at low currents. To verify for ESD damage, check for “light on”

and Vf of the suspect LEDs at low currents.

The Vf of “good” LEDs should be>2.0V@0.1mA for InGaN product and >1.4V@0.1mA for AlInGaP

product.

antistatic notice-smd led

LED dirve IC by Maxim Integrated

MAX6959 4½-Digit LED Display Driver

MAX6958 4½-Digit LED Display Driver

MAX6955 7-, 14-, 16-Segment LED Display Driver

MAX6956 LED Static Display Driver and I/O Port

MAX6954 7-, 14-, 16-Segment LED Display Driver

MAX6952 5 x 7 Matrix LED Display Driver

MAX6957 LED Static Display Driver and I/O Port

MAX6950 5-Digit LED Display Driver

MAX6951 8-Digit LED Display Driver

ICM7212 4-Digit LED Driver

ICM7212A 4-Digit LED Driver

ICM7212AM 4-Digit LED Driver

ICM7212M 4-Digit LED Driver

ICM7218A 8-Digit LED Driver

ICM7218B 8-Digit LED Driver

ICM7218C 8-Digit LED Driver

ICM7218D 8-Digit LED Driver

MAX7221 8-Digit LED Display Driver

MAX7219 8-Digit LED Display Driver

provide in-depth design and IC selection help for design engineers. Each solution is dedicated to a popular end-equipment type and features design information, circuits and a block diagram. Within a block diagram, click on a block to view best-fit integrated circuits recommended by Maxim engineers.

Industrial

Control and Automation
Embedded Computing
Sensors and Field Instruments
Smart Energy

Medical

Diagnostics Monitoring and Therapy
Medical Imaging

Consumer

Consumer

Automotive

Electric Vehicles
Infotainment
Automotive Systems

Computing

Computing

Communications

Cable
Wireless
Data Communications