![Dot matrix LED 8x8-white-blue-green-yellow-red](/pic/BL-M15X88-LED-dot-matrix.jpg)
Brand | BETLUX |
Part NO | BL-M15C883,BL-M15D883 |
Dimension | 37.60*37.60*10.30 mm |
Weight | 13.5000g |
Package | 25pcs/bag |
Datasheet | ![]() |
1,5 дюйма высотой 8x8 светодиодов матричных
1,5 дюйма Матрица Высота (36.60mm)
3.70mm размер точки, окружности точка
колонке: 8 строк: 8
Widthxheight: 37,60 × 37.600mm
Одиночный цвет
низкой текущей операции
Высокая контрастность и легких
выход Совместимость с ASCII и EBCDIC />
Колонка катода и анода колонке доступна
Простой монтаж на PCBoards или Sockets
категориям для световой
интенсивности Технически прочный
Стандарт: Гари поверхности и белой точкой
соответствие RoHS
P >
Electrical-optical characteristics:
Row Cathode | Part No (row anode, column cathode) | color | wavelength | V typical(V) | V max(V) | Brightness(mcd) |
BL-M15C883S | BL-M15D883S | High Bright Red | 660 | 1.85 | 2.2 | 250 |
BL-M15C883D | BL-M15D883D | Super Bright Red | 660 | 1.85 | 2.2 | 320 |
BL-M15C883UR | BL-M15D883UR | Ultra Bright Red | 660 | 1.85 | 2.2 | 400 |
BL-M15C883UHR | BL-M15D883UHR | Ultra Breight Red | 645 | 2.1 | 2.5 | 400 |
BL-M15C883E | BL-M15D883E | Orange | 635 | 2.1 | 2.5 | 190 |
BL-M15C883UE | BL-M15D883UE | High Bright Orange | 630 | 2.1 | 2.5 | 235 |
BL-M15C883YO | BL-M15D883YO | Ultra Amber | 619 | 2.1 | 2.5 | 235 |
BL-M15C883Y | BL-M15D883Y | Yellow | 585 | 2.1 | 2.5 | 190 |
BL-M15C883UY | BL-M15D883UY | High Bright Yellow | 590 | 2.1 | 2.5 | 235 |
BL-M15C883G | BL-M15D883G | Green | 570 | 2.2 | 2.5 | 195 |
BL-M15C883UG | BL-M15D883UG | High Bright Green | 574 | 2.2 | 2.5 | 250 |
BL-M15C883PG | BL-M15D883PG | Super Pure Green | 525 | 3.0 | 4.2 | 270 |
BL-M15C883B | BL-M15D883B | Super Bright Blue | 470 | 2.7 | 4.2 | 180 |
BL-M15C883W | BL-M15D883W | White | - | 2.7 | 4.2 | 235 |
Package configuration & Internal circuit diagram
Absolute maximum ratings (Ta= 25?C)
Reflector Surface color (1st number)/ dot Lens color (2nd number):
Number | 0 | 1 | 2 | 3 | 4 | 5 |
Ref Surface Color | White | Black | Gray | Red | Green | |
Dot Epoxy Color | Water clear | White diffused | Red Diffused | Green Diffused | Yellow Diffused |
Absolute maximum ratings (Ta= 25°C)
Parameter | S | D | UR | E | Y | G | Unit | |
Forward Current IF | 25 | 25 | 25 | 25 | 25 | 30 | mA | |
Power Dissipation Pd | 60 | 60 | 60 | 60 | 60 | 65 | mW | |
Reverse Voltage VR | 5 | 5 | 5 | 5 | 5 | 5 | V | |
Peak Forward Current IPF (Duty 1/10 @1KHZ) | 150 | 150 | 150 | 150 | 150 | 150 | mA | |
Operation Temperature TOPR | -40 to +80 | °C | ||||||
Storage Temperature TSTG | -40 to +85 | °C | ||||||
Lead Soldering Temperature TSOL | Max.260+ 5°C for 3 sec Max. ( 1.6mm from the base of the epoxy bulb) | °C |
Absolute maximum ratings (Ta= 25°C)
Parameter | UHR | UE | YO | UY | UG | PG | UB | UW | Unit |
Forward Current IF | 30 | 30 | 30 | 30 | 30 | 30 | 30 | 30 | mA |
Power Dissipation Pd | 75 | 65 | 65 | 65 | 75 | 110 | 120 | 120 | mW |
Reverse Voltage VR | 5 | 5 | 5 | 5 | 5 | 5 | 5 | 5 | V |
Peak Forward Current IPF (Duty 1/10 @1KHZ) | 150 | 150 | 150 | 150 | 150 | 150 | 100 | 100 | mA |
Operation Temperature TOPR | -40 to +80 | °C | |||||||
Storage Temperature TSTG | -40 to +85 | °C | |||||||
Lead Soldering Temperature TSOL | Max.260+ 5°C for 3 sec Max. ( 1.6mm from the base of the epoxy bulb) | °C |
Partno description:
LED dot matrix is widely used in LED information board indoor and semi-outdoor
Applied for:
1. Application
The Dot Matrix display is widely applied for ordinary electronic equipment (such as office equipment,
communication equipment and household applications). Checking with BETLUX's Sales in
advance for information on applications in which exceptional reliability is required, particularly
when the failure or malfunction of the dot matrix LEDs may directly jeopardize life or health (such as in
aviation, transportation, traffic control equipment, medical and life support systems and safety
devices).
2. Storage
The storage ambient for the Seven Segment LED should not exceed 30℃ temperature or 70% relative humidity.
For extended storage out of their original packaging, it is recommended that the Seven Segment LEDs be stored
in a sealed container with appropriate desiccant, or in a desiccator with nitrogen ambient.
3. Cleaning
Avoid using any unspecified chemical solvent to clean LED . For example, Trichloroethylene, Chlorosen, Acetone, and Diflon S3MC.
Any cleaning method can only be taken under normal temperature in one minute or less if it is required.
Use water to clean the Dot MatrixLED if necessary under room temperature
dry it immediately after that.
4.Forming
Any unsuitable stress applied to the epoxy may break bonding wires in Dot matrix LED
Any forming on lead pin must be done before soldering, not during or after soldering.
Avoid applying any stress to resin in order to prevent the epoxy fracture and break on bonding wire.
While forming, please use a tie bar cut or equivalent to hold or bend the pin.
2mm from the base of resin is the minimum distance for the place bending the lead pin.
Avoid bending the lead pin at the same point twice or more.
Soldering
When soldering, leave a minimum of 2mm clearance from the base of the base of the lens to the soldering point. Dipping the lens into the solder must be avoided.
Do not apply any external stress to the lead frame during soldering while the LED is at high temperature.
Recommended soldering conditions:
Wave Soldering | Soldering Iron | ||
Pre-Heat | 100°C Max. | Temperature | 300°C Max. |
Pre-Heat Time | 60sec Max. | ||
SolderWave | 260°C Max. | Soldering Time | 3sec Max.(one time only) |
Soldering Time | 5sec Max. |
Note: Excessive soldering temperature and/or time might result in deformation of the LED lens or failure of the LED
Static Electricity or power surge will damage the LED.
Suggestions to prevent ESD damage:
n Use a conductive wrist band or anti-electrostatic glove when handling these LEDs
n All devices, equipment, and machinery must be properly grounded
n Work tables, storage racks, etc. should be properly grounded
n Use ion blower to neutralize the static charge which might have built up on surface of the LED's
plastic lens as a result of friction between LEDs during storage and handling
ESD-damaged LEDs will exhibit abnormal characteristics such as high reverse leakage current,
low forward voltage, or “no light on” at low currents. To verify for ESD damage, check for “light on”
and Vf of the suspect LEDs at low currents.
The Vf of “good” LEDs should be>2.0V@0.1mA for InGaN product and >1.4V@0.1mA for AlInGaP
product.
MAX6979 16-Port, 5.5V LED Driver with LED Fault Detection and Watchdog
MAX6971 16-Port, 36V LED Driver
MAX6962 4-Wire Serially Interfaced 8 x 8 Matrix Graphic LED Drivers
MAX6963 4-Wire Serially Interfaced 8 x 8 Matrix Graphic LED Drivers
MAX6960 8x8 Graphic Matrix LED driver
MAX6961 4-Wire Serially Interfaced 8 x 8 Matrix Graphic LED Drivers
MAX6969 16-Port, 5.5V LED Driver
MAX6978 8-Port, 5.5V LED Driver with Fault Detection and Watchdog
MAX6977 8-Port, 5.5V LED Driver with Fault Detection
MAX6968 8-Port, 5.5V LED Driver
MAX6967 LED Driver with PWM Intensity Control
MAX6966 LED Driver with PWM Intensity Control
MAX6964 LED Driver with PWM Intensity Control
MAX6965 LED Driver with PWM Intensity Control
MAX6953 5 x 7 Matrix LED Display Driver